3/28/2023 0 Comments Biff hoverboardIn the third film, a note left by Doc's 1885 self reveals that the DeLorean's flying circuits (added by him in 2015) were destroyed by the strike. In the second film, the destination time display malfunctions and begins to show a series of random dates, causing Doc to be sent back to 1885 when the DeLorean is struck by lightning with him inside. In the first film, the car has starter problems and has a hard time restarting once stopped, much to Marty's repeated frustration. The DeLorean suffers assorted malfunctions and damage over the course of the trilogy. Vents on the back heat the vehicle after time travel. After the trip, the exterior of the DeLorean is extremely cold, and frost forms from atmospheric moisture all over the car's body. In the destination time, immediately before the car's arrival, three large and loud flashes occur at the point from which the car emerges from its time travel. Observers outside the vehicle see an implosion of plasma as the vehicle disappears, leaving behind a trail of fire aligned with the DeLorean's tires (which can also appear in midair), while occupants within the vehicle see a quick flash of light and instantaneously arrive at the target time in the same spatial location (relative to the Earth) as when it departed. The actual speedometer on the production DeLorean's dashboard only goes up to 85 mph, and the car itself was criticized for being underpowered. Various proposals have been brought forth in the past by fans of the movie franchise for why the car has to be moving at 88 mph to achieve temporal displacement, but actually the production crew chose the velocity simply because they liked how it looked on the speedometer, modified for the movie. A digital speedometer is attached to the dashboard so that the operator can accurately gauge the car's speed. Surrounded by an electrical current similar to a Tesla coil, the whole car vanishes in a flash of white/blue light seconds later, leaving a pair of fiery tire tracks. As it accelerates, several coils around the body glow blue/white while a burst of light appears in front of it. After entering a target date with the keypad inside the DeLorean, the operator accelerates the car to 88mph (142km/h), which activates the flux capacitor. The operator is seated inside the DeLorean (except the first time, when the remote control is used), and turns on the time circuits by turning a handle near the gear lever, activating a unit containing multiple fourteen- and seven-segment displays that show the destination (red), present (green), and last departed (yellow) dates and times. Place a big drop at the cuticle and hold brush parallel to the nail while applying trying not to touch the nail with the bristles, this helps prevents smearing.The control of the time machine is the same in all three films. When design is completely dry on your nail, apply a layer of fresh top coat with as few strokes as possible.Remove excess nail polish from your skin and cuticles by using a flat brush or cotton swab dipped in acetone or nail polish remover, you could use tape to lift excess polish from your skin as well. With a squishier stamper push the stamper straight to the nail, with other stamper heads it might work better to roll it once from side to side to transfer image. Quickly transfer the image from the stamper onto a nail with an oil free and completely dry base color.If your image does not transfer you may need to work faster, scrape differently (less pressure or new angle), prime your stamper (with acetone or gentle nail file/buffer) or try another opaque nail polish that doesn’t dry very fast.Immediately after scraping, quickly transfer the design to your stamper by lightly rolling once across the design from one side to the other or pushing once straight into the design.Try to only scrape once, do not push card to plate too hard and work as quickly as possible to avoid drying. Hold a plastic card firmly at a 45 degree angle and lightly scrape across the plate to remove excess polish.Try another polish if you are not getting results you want. Special stamping polishes are recommended but opaque nail polishes that do not dry very fast also work well. Quickly apply a thick layer of nail polish in a few strokes over the design you wish to stamp.Сlean your stamper with tape by using the sticky side to remove dry polish. When you first receive your plate and after every use wipe clean your plate with acetone or non-acetone nail polish remover without oils. Remove your new stamping plate from its packaging and remove the plastic protective film from over the metal.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |